Unanswered Questions
368 questions with no upvoted or accepted answers
6
votes
0
answers
745
views
nRF24L01 continuously reading closed pipe
I am testing communication between two nRF24L01 modules. The receiver is getting the transmitted message but is also continuously reading (null) data from a closed pipe? I am using the RF24 by TMRh20 ...
- 121
5
votes
0
answers
1k
views
Manchester 433MHz Nano to ATTiny85
My transmitter is a Nano, the receiver is a Tiny85.
I use a Logic Analyzer to check if stuff is moving, I can clearly see data coming in at the receiver.
The receiver does not 'decode' the data, man....
- 2,522
4
votes
0
answers
76
views
Can I use regular pins (Example: D2, A3, etc...) as serial (RX, TX)?
Python/Arduino Beginner here...
I have a DFplayer I am trying to hook to my Arduino and I want to hook it up through the regular pins instead of the RX and TX pins, but I've not been able to find ...
- 41
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
121
views
Keypad - Speaker - Interference
I am trying to build a system, that plays specific audios (.wav files) from a SD-Card, according to the key combination that has been pressed.
I am using:
4x4 Membrane
4 Ohm Speaker
MicroSD Card ...
- 1,795
3
votes
0
answers
551
views
nRF24L01+ problem with receiving response
I'm sending currently data from a Raspberry to an Arduino, but I have a problem with receiving response from the Arduino back to the Raspberry:
Sent the message: ['H', 'i', '.', '.', 'A', 'r', 'd', '...
- 31
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
0
answers
2k
views
Arduino Bluetooth upload problem HC-05 v4.0
I upload code into arduino nano using a self-made PCB with bluetooth using this method. I was initially using Arduino Nano (chinese Clone, the one with CH340G) and Bluetooth module HC-05 (version 3.0) ...
3
votes
1
answer
2k
views
Creating a sine wave with a DAC and feeding it back
I want to produce a digital sine wave, send it to DAC0, and then receive it back as input on A0 and plot the graph. I am using an Arduino Due. I wrote the following code:
#define maxSamplesNum 120
#...
CommunityBot
- 1
3
votes
0
answers
653
views
Arduino nano clone problem with interrupt on falling edge on pin 2
I've s 1Hz square wave coming from a DS1307 SQW/OUT pin going into pin2 on the Nano that is set up as input with internal pullup enabled.
I've set up the interrupt on falling edge but I can't get the ...
- 2,522
3
votes
0
answers
378
views
Connecting Arduino Due's DAC output to pc sound card with protection
I would like to connect the DAC outputs of my arduino board to my pc sound card input so that I can use my sounds card as an osciloscope.
I have two questions:
1- if I don't use an amplifier, how ...
- 241
3
votes
0
answers
129
views
Reading Reveive Hold Register from USART in SPI Mode on Arduino Due
Sending with this function here works fine:
uint16_t usart0spiTransfer16(uint16_t spiMessage16) {
uint16_t sdo = 0;
byte firstByte = spiMessage16;
byte secondByte = (spiMessage16 >> ...
- 2,522
3
votes
0
answers
323
views
Arduino Due upload firmware issue
I have Arduino Due on SAM3x8e. I'm on Ubuntu 14.04. Before today I uploaded firmware via terminal using those commands:
$ stty -F /dev/ttyACM0 speed 1200 cs8 -cstopb -parenb
$ /home/q/apps/devel/...
- 151
3
votes
0
answers
883
views
Arduino Due native programming port
Arduino does not recommend to program the Due board via Native port as it is not reliable:
If the MCU crashed for some reason it is likely that the soft erase procedure won't work as this procedure ...
- 111