Unanswered Questions
418 questions with no upvoted or accepted answers
6
votes
0
answers
745
views
nRF24L01 continuously reading closed pipe
I am testing communication between two nRF24L01 modules. The receiver is getting the transmitted message but is also continuously reading (null) data from a closed pipe? I am using the RF24 by TMRh20 ...
- 121
5
votes
0
answers
1k
views
Manchester 433MHz Nano to ATTiny85
My transmitter is a Nano, the receiver is a Tiny85.
I use a Logic Analyzer to check if stuff is moving, I can clearly see data coming in at the receiver.
The receiver does not 'decode' the data, man....
- 2,522
4
votes
0
answers
76
views
Can I use regular pins (Example: D2, A3, etc...) as serial (RX, TX)?
Python/Arduino Beginner here...
I have a DFplayer I am trying to hook to my Arduino and I want to hook it up through the regular pins instead of the RX and TX pins, but I've not been able to find ...
- 41
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
4
votes
2
answers
137
views
Turn ESP8266 into an Arduino IDE-like "sketch uploader" (over hardware serial)
I have an ESP8266 module which has downloaded a hex file for an Arduino Mega2560. This hex file (call it mega2560.hex) is sitting in the ESP's SPIFFS file system. What I want to do is basically ...
- 18.2k
3
votes
2
answers
381
views
Is is possible to install a bootloader to an Arduino clone without a physical programmer?
I got an Arduino UNO clone, connected it to my PC via USB. I can't upload any sketches.
Correct board and port are selected in the IDE.
Windows recognizes it as a device, even though it has a CH340 (...
CommunityBot
- 1
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
121
views
Keypad - Speaker - Interference
I am trying to build a system, that plays specific audios (.wav files) from a SD-Card, according to the key combination that has been pressed.
I am using:
4x4 Membrane
4 Ohm Speaker
MicroSD Card ...
- 1,795
3
votes
0
answers
551
views
nRF24L01+ problem with receiving response
I'm sending currently data from a Raspberry to an Arduino, but I have a problem with receiving response from the Arduino back to the Raspberry:
Sent the message: ['H', 'i', '.', '.', 'A', 'r', 'd', '...
- 31
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
0
answers
2k
views
Arduino Bluetooth upload problem HC-05 v4.0
I upload code into arduino nano using a self-made PCB with bluetooth using this method. I was initially using Arduino Nano (chinese Clone, the one with CH340G) and Bluetooth module HC-05 (version 3.0) ...
3
votes
1
answer
2k
views
Creating a sine wave with a DAC and feeding it back
I want to produce a digital sine wave, send it to DAC0, and then receive it back as input on A0 and plot the graph. I am using an Arduino Due. I wrote the following code:
#define maxSamplesNum 120
#...
CommunityBot
- 1
3
votes
0
answers
653
views
Arduino nano clone problem with interrupt on falling edge on pin 2
I've s 1Hz square wave coming from a DS1307 SQW/OUT pin going into pin2 on the Nano that is set up as input with internal pullup enabled.
I've set up the interrupt on falling edge but I can't get the ...
- 2,522
3
votes
0
answers
214
views
Atmel SAM MCU (on Arduino Due) only boots after second power up
I am using an Arduino Due as a prototyping board for a microcontroller project. The due has the chip Atmel ATSAM3X8E, with an ARM Cortex-M3 core. I am programming the flash directly using Atmel Studio ...
GrixM
3
votes
0
answers
378
views
Connecting Arduino Due's DAC output to pc sound card with protection
I would like to connect the DAC outputs of my arduino board to my pc sound card input so that I can use my sounds card as an osciloscope.
I have two questions:
1- if I don't use an amplifier, how ...
- 241