Skip to main content
Electrical Engineering

Nice Question

 Nice Question
Question score of 10 or more. This badge can be awarded multiple times.
Awarded 6064 times.
Why is a forward converter called a forward converter?
Awarded yesterday
How much background "noise" is normal on an oscilloscope
Awarded 2 days ago
Controlling heater with PWM through MOSFET
Awarded May 3 at 6:56
What are 'induced atmospheric variations', and how do they cause grid desynchronization? (Current Spain-wide power outage)
Awarded Apr 29 at 17:08
How to protect input against both ESD and reverse polarity?
Awarded Apr 26 at 16:27
Regulator blowing up. Does it need more protection?
Awarded Apr 17 at 18:31
x86 Motherboard Bring Up - Intel Tiger Lake UP3 CPU
Awarded Apr 17 at 6:26
Why do they need so many capacitors here instead of one single capacitor?
Awarded Apr 16 at 9:17
Unidirectional or Bi-directional TVS diodes - Which one to use?
Awarded Apr 16 at 9:09
Why not double the radio bandwidth using polarization?
Awarded Apr 13 at 7:43
How hazardous is simply handling leaded solder?
Awarded Apr 12 at 14:10
Is there a rule of thumb for what frequencies analog vs. digital signal integrity starts to matter?
Awarded Apr 12 at 7:50
Does neutral wire carry power?
Awarded Apr 9 at 6:01
In a series circuit, does the first component briefly receive full voltage before the electric field propagates?
Awarded Apr 8 at 15:30
"Shooting" 9V battery; what causes it?
Awarded Apr 8 at 4:58
Does solder expire?
Awarded Apr 7 at 15:26
Can decoupling capacitors still do their job when placed on the back layer?
Awarded Apr 7 at 13:51
How can I convert this vintage digital alarm clock from 50 Hz to 60 Hz?
Awarded Apr 4 at 17:57
Standard length of male header pins
Awarded Apr 3 at 15:58
SPDT in LTspice
Awarded Mar 31 at 7:19
Which is the better PCB layout for decoupling capacitors?
Awarded Mar 28 at 5:24
1 kHz clock over long wire
Awarded Mar 25 at 20:40
Does the value of a resistor matter when doing voltage division to cut it into a half?
Awarded Mar 25 at 20:36
How does soldering affect the internal bonding between the IC die and its package?
Awarded Mar 23 at 4:34
Active analog summing circuit with very high noise floor
Awarded Mar 22 at 13:36
How much current can a 0.1" pitch pin header pass?
Awarded Mar 18 at 11:20
How to specify a capacitor in Altium schematic as DNP
Awarded Mar 17 at 18:11
What type of fire extinguisher do I need for lithium polymer batteries?
Awarded Mar 14 at 11:27
Detecting phase between square wave and sine wave signals
Awarded Mar 13 at 17:05
Do you have to use an instrumentation amplifier to measure voltage across a 0.01 ohm shunt?
Awarded Mar 11 at 16:22
DCF77 (AM 77.5 kHz) receiver in discrete components?
Awarded Mar 10 at 13:40
Why does the powerline frequency have anything to do with TV framerate?
Awarded Mar 9 at 19:50
Putting an Ammeter in Parallel with a Wire but Still Having Series-Resistors
Awarded Mar 8 at 17:55
TP4056 module parallel output
Awarded Mar 7 at 0:54
Is it bad practice to drive an op amp into saturation to shut it down?
Awarded Mar 6 at 22:26
Altium - Cannot Select/highlight components on PCB
Awarded Mar 4 at 8:31
Is it going to be possible to write code in C++ for PIC microcontrollers in the future?
Awarded Feb 27 at 18:07
Switching inductive loads without flyback diodes
Awarded Feb 26 at 22:21
Circuit for wiping / destroying IC on a smart card
Awarded Feb 23 at 23:01
Why is the ESR curve of C0G MLCC not smooth at low frequencies?
Awarded Feb 20 at 20:20
Why does ATSAM3X8E have two separate registers for setting and clearing bits?
Awarded Feb 17 at 12:54
Paint for a printed circuit board for finding the heat dissipation
Awarded Feb 12 at 18:05
Why does the voltage drop across a given resistor change when I add more resistors to a circuit?
Awarded Feb 11 at 3:18
Cheap thermocouples. Homemade?
Awarded Feb 10 at 1:11
Air gap on isolation space
Awarded Feb 9 at 13:16
What is the "Eco1.User" layer in KiCad?
Awarded Feb 8 at 8:34
Max operating temp of IC's
Awarded Feb 7 at 23:14
Micro Connector identification
Awarded Feb 6 at 15:06
How can we raise a surface mount component 0.4mm off of the PCBA?
Awarded Feb 6 at 13:41
Why do strain gauges often have two wires connected to the same pad?
Awarded Feb 4 at 19:51
Extending the Delta-Wye/∆-Y Transformation to higher polygons
Awarded Feb 4 at 11:04
Why is neutral wire connected to ground at the transformer?
Awarded Feb 2 at 3:37
How to .step through different diodes
Awarded Jan 31 at 8:37
Difference between Mosfet and Voltage Regulator?
Awarded Jan 30 at 0:51
Why use a tantalum instead of a ceramic capacitor?
Awarded Jan 29 at 13:11
What is this PCB to PCB joint without a connector called?
Awarded Jan 24 at 17:34
Transistors in LM108 op-amp
Awarded Jan 23 at 16:23
Why do I need a USB-C controller for PD?
Awarded Jan 23 at 15:04
Why do PC Fans use a separate PWM line?
Awarded Jan 20 at 16:58
What is the I2C ACK, and how do I detect it?
Awarded Jan 18 at 20:42
1
2 3 4 5
…
102