Unanswered Questions
337 questions with no upvoted or accepted answers
0
votes
0
answers
37
views
How does a sensor data move from physical layer to application layer
I have used Arduino IDE to program a IOT gateway using ESP32 and W5500 ethernet module to use them as a ethernet webserver.
I wanted to know for educational purpose, I know that sensor belong to ...
- 11
1
vote
2
answers
43
views
Can't sync ESP32 with Blynk
I was trying to display the readings of my dht11 sensor on the Blynk dashboard but I am struggling a lot. A little help would be really appreciated.
#define BLYNK_PRINT Serial
/* Fill in information ...
- 100
0
votes
2
answers
59
views
How can you trace out the short-term trajectory of a 6DOF IMU
I've looked and looked on forums, wrote prompt after prompt in DeepSeek and ChatGPT but I've hit a roadblock.
I'm currently working on a project where I want to write numbers in the air using a ...
0
votes
0
answers
99
views
ESP32 Upload Fails: “Failed to connect to ESP32: No serial data received” (Worked Previously)
I’m trying to upload code to my ESP32 board using the Arduino IDE, but I’m consistently getting the following error:
A fatal error occurred: Failed to connect to ESP32: No serial data received.
For ...
- 1,773
0
votes
1
answer
53
views
ESP32 Timers - Controller Crashes Above 240 kHz, Duty Cycle Becomes Unstable
I'm trying to generate three synchronized signals on ESP32 for a device that requires precise timing. However, when I increase the frequency above 240 kHz, the controller crashes, and the duty cycle ...
CommunityBot
- 1
-1
votes
1
answer
67
views
Getting a WDT reset on ESP32
I have a project that uses a GY-53 BMP180 and ESP32.
Each time I connect ESP32 to USB after uploading, I get this error:
22:27:27.352 -> rst:0x8 (TG1WDT_SYS_RESET),boot:0x13 (...
- 143
1
vote
1
answer
102
views
ESP32-S3 Does not read BME680 Data
I build a PCB using ESP32-S3-WROOM-1-N16R2 Controller. I programmed a BME680 sensor with this MCU. My pinouts are,
BME_SCK 38
BME_MISO 19
BME_MOSI 15
BME_CS 5
This is my Arduino code,
#include <...
CommunityBot
- 1
1
vote
0
answers
87
views
"Stack canary watchpoint triggered (loopTask)" when synchronizing with Arduino Cloud IoT (ArduinoCloud.update())
I have created a sketch that updates 195 variables : 16xString variables, 34xfloat, 52xint, 107xbool.
Notice : I'm using the IDE tool instead of the included Cloud IoT compile (because I have a pb ...
0
votes
0
answers
25
views
ESP32 Bluetooth Pair scanFilter not working properly
I am trying to make a bluetooth device with esp32 s3. Pairing should work like a headfone. At the First start, any device can connect my ble ESP32 after connecting I will add in whitelist this device ...
- 297
0
votes
0
answers
49
views
Multiple esp32s running on batter power using ESP-NOW
I have a project where I'd like to have two esp32s communicate using ESP-NOW, but both running on battery. I'd like for both to be in deep sleep, wake up and communicate, and go back to sleep, repeat.
...
0
votes
0
answers
72
views
Get Hash from Biometric Fingerprint Data for Encryption
I'm trying to get a reliable hash from a fingerprint scanner to use as a encryption key. According to this post here: https://crypto.stackexchange.com/questions/103693/can-you-restore-a-private-key-...
- 101
0
votes
0
answers
16
views
Are sleep and reset on DRV8825 tied up to GND?
I am working on a project that has a servo and a stepper motor, so I build a circuit which have both the driver and lm7805.
The problem is that the regulator overheated very quickly. I traced the ...
- 1,525
1
vote
0
answers
60
views
`__has_include` macro on ESP board
I am working on a code for ESP boards that can be used on either ESP32 or ESP8266 and I want to make sure I include the correct libraries.
I know I can check if ESP32 OR ESP8266 are defined, but I ...
- 201
-1
votes
1
answer
176
views
Stepper motor turns unexpectedly slowly
I want to control a stepper motor using my esp32 and an USB connection. I seem to have some issue understanding why the stepper motor runs very slowly - I suspect it's because power to the motor is ...
- 155
1
vote
0
answers
147
views
How do I enable CONFIG_SPIRAM_SUPPORT for ESP32 S3 on Arduino?
I'm trying to use PSRAM with the TFT_eSPI library, but it fails because CONFIG_SPIRAM_SUPPORT isn't defined.
In Arduino -> Tools -> PSRAM I selected OPI PSRAM as the board manufacturer (the ...
- 239