Unanswered Questions
691 questions with no upvoted or accepted answers
6
votes
0
answers
745
views
nRF24L01 continuously reading closed pipe
I am testing communication between two nRF24L01 modules. The receiver is getting the transmitted message but is also continuously reading (null) data from a closed pipe? I am using the RF24 by TMRh20 ...
- 121
5
votes
0
answers
1k
views
Manchester 433MHz Nano to ATTiny85
My transmitter is a Nano, the receiver is a Tiny85.
I use a Logic Analyzer to check if stuff is moving, I can clearly see data coming in at the receiver.
The receiver does not 'decode' the data, man....
- 2,522
4
votes
0
answers
76
views
Can I use regular pins (Example: D2, A3, etc...) as serial (RX, TX)?
Python/Arduino Beginner here...
I have a DFplayer I am trying to hook to my Arduino and I want to hook it up through the regular pins instead of the RX and TX pins, but I've not been able to find ...
- 41
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
4
votes
0
answers
471
views
Problem in using COZIR W-100 with arduino
I was using the COZIR W-100 carbon dioxide sensor with an Arduino Mega 2560 with the example code from this site.
But the measured value of carbon dioxide by sensor was 90 ppm in fresh air and that ...
4
votes
0
answers
175
views
Can d2xx connect to an arduino mega 250?
I am trying to replace a device which used a FTDI chip (http://www.ftdichip.com/Drivers/D2XX.htm) to get USB to serial. I need some more code on the chip, so I want to use an arduino mega 2560 instead....
- 41
4
votes
0
answers
7k
views
Arduino GSM receiving text and then storing value as a variable in code
I am using an Arduino Mega board with a SIM900 GSM.
My goal is to be able to text the GSM with a value of two digits (ex: 79) and then store that value as a variable in the code. I know how to set ...
4
votes
2
answers
137
views
Turn ESP8266 into an Arduino IDE-like "sketch uploader" (over hardware serial)
I have an ESP8266 module which has downloaded a hex file for an Arduino Mega2560. This hex file (call it mega2560.hex) is sitting in the ESP's SPIFFS file system. What I want to do is basically ...
- 18.2k
3
votes
0
answers
490
views
Integration of MAX30100 and DS18B20 Thermal Probe Integration
This is for my final year project that I have been tasked with designing a patient monitoring system. However, during the last stretch of model prototyping, I am experiencing issues with my MAX30100 ...
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
2k
views
BLE HM10 - Set Password - Android Pairing Problem
I have developed an application on Android, which connects to a Bluetooth HM10, launches commands, and turns LEDs on and off through my Arduino. All of this works properly.
So, I want to make ...
3
votes
0
answers
121
views
Keypad - Speaker - Interference
I am trying to build a system, that plays specific audios (.wav files) from a SD-Card, according to the key combination that has been pressed.
I am using:
4x4 Membrane
4 Ohm Speaker
MicroSD Card ...
- 1,795
3
votes
0
answers
551
views
nRF24L01+ problem with receiving response
I'm sending currently data from a Raspberry to an Arduino, but I have a problem with receiving response from the Arduino back to the Raspberry:
Sent the message: ['H', 'i', '.', '.', 'A', 'r', 'd', '...
- 31
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
0
answers
2k
views
How to extract fingerprint template from Arduino Fingerprint Sensor
How to extract fingerprint template from Arduino Fingerprint Sensor and store it to SD card module using adafruit library and then search/import it from SD card module when tapping the fingerprint?
...
- 610