Unanswered Questions
663 questions with no upvoted or accepted answers
6
votes
0
answers
745
views
nRF24L01 continuously reading closed pipe
I am testing communication between two nRF24L01 modules. The receiver is getting the transmitted message but is also continuously reading (null) data from a closed pipe? I am using the RF24 by TMRh20 ...
- 121
5
votes
0
answers
903
views
Internet in ESP32 is not working with IPv6
I am using ESP-WROOM-32D in STA mode with Arduino IDE(2.0.5) ESP32 board(2.0.9).
I am trying to do http post request with ESP32. Router that provides internet supports only IPv6.
Here I am getting ...
- 3,126
5
votes
0
answers
1k
views
Manchester 433MHz Nano to ATTiny85
My transmitter is a Nano, the receiver is a Tiny85.
I use a Logic Analyzer to check if stuff is moving, I can clearly see data coming in at the receiver.
The receiver does not 'decode' the data, man....
- 2,522
4
votes
0
answers
140
views
Arduino IDE v 2.2.1 log file not limited in size (on Ubuntu 23.04)
I was learning/building with a new Arduino Nano ESP32 yesterday and left the Arduino IDE running overnight on Ubuntu 23.04 and it used all the space on my hard drive to write log files which broke my ...
4
votes
0
answers
2k
views
Is there a way to use ESP8266 in promiscuous(monitor) mode and see the the wifi packets?
I didn't find much documentation about ESP promiscuous mode (just from the espressif sdk although I'm using ArduinoIDE https://docs.espressif.com/projects/esp8266-rtos-sdk/en/latest/api-reference/wifi/...
- 73
4
votes
0
answers
76
views
Can I use regular pins (Example: D2, A3, etc...) as serial (RX, TX)?
Python/Arduino Beginner here...
I have a DFplayer I am trying to hook to my Arduino and I want to hook it up through the regular pins instead of the RX and TX pins, but I've not been able to find ...
- 41
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
3
votes
0
answers
1k
views
How to use C++20 in Arduino IDE?
I'm writing a program for esp32 using the Arduino IDE that needs to count the number of '1' bits in a byte.
I found a post elsewhere that says there's a nice function in the standard library to do it: ...
- 1,595
3
votes
0
answers
783
views
How can I connect my ESP32-WROOM-32 to Arduino IDE?
I'm using this 'ESP32-WROOM-32' but I can't find the correct board in the IDE. I see the esp32-wroom-DA (edit, i took it to the store where i bought it and it worked fine with theirs. they were on ...
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
121
views
Keypad - Speaker - Interference
I am trying to build a system, that plays specific audios (.wav files) from a SD-Card, according to the key combination that has been pressed.
I am using:
4x4 Membrane
4 Ohm Speaker
MicroSD Card ...
- 1,795
3
votes
0
answers
551
views
nRF24L01+ problem with receiving response
I'm sending currently data from a Raspberry to an Arduino, but I have a problem with receiving response from the Arduino back to the Raspberry:
Sent the message: ['H', 'i', '.', '.', 'A', 'r', 'd', '...
- 31
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
0
answers
2k
views
Arduino Bluetooth upload problem HC-05 v4.0
I upload code into arduino nano using a self-made PCB with bluetooth using this method. I was initially using Arduino Nano (chinese Clone, the one with CH340G) and Bluetooth module HC-05 (version 3.0) ...
3
votes
0
answers
5k
views
String.format("%i",i) equivalent
How do I format an arduino String when I do not want to print it?
I know that one can use printf() or other methods to print a formated string and unfortunately that's all I find with google.
But that'...
- 1,868