Unanswered Questions
220 questions with no upvoted or accepted answers
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
4
votes
0
answers
175
views
Can d2xx connect to an arduino mega 250?
I am trying to replace a device which used a FTDI chip (http://www.ftdichip.com/Drivers/D2XX.htm) to get USB to serial. I need some more code on the chip, so I want to use an arduino mega 2560 instead....
- 41
3
votes
1
answer
151
views
Arduino R3 Uno Clone - When barrel plug connected there is 5V on USB. Why?
I have been using Arudino Megas for some projects and never had this problem.
Simply enough - I am powering arduino with 12V in via barrel and take power out via VIN to 12V low very low current small ...
CommunityBot
- 1
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
1
answer
2k
views
Creating a sine wave with a DAC and feeding it back
I want to produce a digital sine wave, send it to DAC0, and then receive it back as input on A0 and plot the graph. I am using an Arduino Due. I wrote the following code:
#define maxSamplesNum 120
#...
CommunityBot
- 1
3
votes
0
answers
400
views
Software flashing attiny167 from RPi with avrdude
I am trying to flash a program onto an attiny167
(already bootloaded with the micronucleus bootloader)
with a Raspberry Pi via avrdude and USB.
Background
I have 50 Raspberry Pi 3B's connected to an ...
CommunityBot
- 1
3
votes
0
answers
328
views
Arduino IDE programs Leonardo but cannot open serial terminal
I'm using Arduino: 1.6.7 (Mac OS X 10.11.3), Board: "Arduino Leonardo".
When I try to program my code, it works without problems.
When I want to open the built-in Serial Monitor or Serial Plotter, ...
- 2,522
3
votes
0
answers
378
views
Connecting Arduino Due's DAC output to pc sound card with protection
I would like to connect the DAC outputs of my arduino board to my pc sound card input so that I can use my sounds card as an osciloscope.
I have two questions:
1- if I don't use an amplifier, how ...
- 241
3
votes
0
answers
129
views
Reading Reveive Hold Register from USART in SPI Mode on Arduino Due
Sending with this function here works fine:
uint16_t usart0spiTransfer16(uint16_t spiMessage16) {
uint16_t sdo = 0;
byte firstByte = spiMessage16;
byte secondByte = (spiMessage16 >> ...
- 2,522
3
votes
0
answers
323
views
Arduino Due upload firmware issue
I have Arduino Due on SAM3x8e. I'm on Ubuntu 14.04. Before today I uploaded firmware via terminal using those commands:
$ stty -F /dev/ttyACM0 speed 1200 cs8 -cstopb -parenb
$ /home/q/apps/devel/...
- 151
3
votes
0
answers
883
views
Arduino Due native programming port
Arduino does not recommend to program the Due board via Native port as it is not reliable:
If the MCU crashed for some reason it is likely that the soft erase procedure won't work as this procedure ...
- 111
3
votes
0
answers
2k
views
Using USB on a Leonardo to receive data from PC
I am new to the Leonardo, having only used a duemilanove before, and I am interested in using it's USB capabilities for a project.
Basically I need it to be an input and output device, communicating ...
- 131
3
votes
0
answers
1k
views
Interfacing WM8731 code to Arduino Due
WM8731 codec was successfully interfaced with Atmega328 like variants in Arduino. It was first done successfully by Open music labs who are the makers of the breakout board for WM8731. Taking this ...
- 2,522
3
votes
1
answer
1k
views
Program SMT32 black-pill without pushing buttons or propriatary devices
Are there any options for programming an STM32 black-pill from the Arduino IDE without first having to manually push buttons to go into DFU mode or having to buy an ST-Link device?
A solution that ...
- 11