Unanswered Questions
195 questions with no upvoted or accepted answers
5
votes
0
answers
361
views
SPI between Master arduino and Slave arduino
How can I send the string from Slave SPI to Master SPI?
I want to write code in Bare Metal.
The problem which I am facing is I can't make out what will be my blocking function in Master SPI code when ...
CommunityBot
- 1
5
votes
0
answers
2k
views
Modbus TCP/IP using Arduino uno and ENC28J60 module
I have this project where I need a modbus tcp server that will host a series of sensor data for other modbus client devices to read. I use this Library by Andresoarmento
This is the code i am using ...
3
votes
0
answers
381
views
Raspberry pi pico (Arduino core) not initialising SPI correctly for NRF24l01
I'm working on a project where i have a Raspberry pi Pico connected to a NRF24l01+ to send some data.
However i'm not recieving any data on the reciever and i think that its because the SPI bus is not ...
- 1,525
3
votes
0
answers
1k
views
ESP32-C3 SPI Class documentation/features?
ESP32-C3 has a nice feature called GPIO Matrix which allows to map most of it's peripherals to any GPIO pin. And it has feature called IO_MUX which allows direct & faster operations for some of ...
- 131
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
793
views
SPI register read returns 0x00 or 0xff
I am trying to interface a Arduino Uno with an ASM330LHH using SPI. Whenever I try to read any register, I either get 0xff or 0x00 on the serial monitor
The code I am using:
#include <SPI.h>
#...
3
votes
0
answers
2k
views
How to use SPI to set/ read registers for a sensor (Avoiding need for Github Lib)
Ok so as some readers might have seen, my current project involves using MPU's. The idea is sending data via CAN bus to a controlling MCU to then send to a raspberry pi to perform the calculations ...
- 99
3
votes
0
answers
220
views
Scheduling and BLE Read on demand
I'm building a data logging device with BLE capability using RFduino.
Sensors are read using timer interrupt to a buffer. When the buffer is full, then the whole buffer is written to SD card.
At the ...
- 2,522
3
votes
0
answers
498
views
SPI communication between two Ethernet Shields (W5100)
I am a newbie to the world of IoT, I want to ask...
Is it possible to connect two Ethernet shields with SPI? And if yes, how can I codes them?
I have reference from http://www.gammon.com.au/spi and ...
- 31
3
votes
0
answers
601
views
Do software SPI read from a register using shiftin()
How to read from a register using software SPI, presumably shiftin()?
It works using the builtin SPI library + hardware SPI.
I seem to be able to write but not read using manual shiftin()/shiftout()...
- 3,198
3
votes
0
answers
921
views
Read from the SD card - ACMD41 times out
I'm trying to read from the SD card using an Arduino Pro Mini (3.3 V), Pololu micro-SD reader (the 3.3V one) over a SPI protocol.
I've tried both the SD library from Arduino SDK, and the Adafruit one....
- 2,522
3
votes
0
answers
199
views
Uno Ethernet shield and TMP36 reading
I am just getting started with my Uno via the Vilros Ultimate Starter Kit. I've done all of the sample circuits and played around with a few other things.
Today I connected the Ethernet shield with ...
- 2,522
2
votes
1
answer
106
views
L9780 and SPI communication
I'm working on a program to interface with a development board I spun for an L9780 - wideband oxygen controller IC. At this point, I'm trying to get a consistent "status" read back but ...
CommunityBot
- 1
2
votes
0
answers
103
views
Slow I2C communication
To collect temperature and BPM, I connected a max30101 in my Heltec WiFi kit V3 with ESP32. The data collected are stored in arrays to extract statistical features from signals which an algorithm will ...
- 31
2
votes
0
answers
298
views
Ability to connect 2 or more w5500 Modules and deal with them as objects
I wish to create a rudimentary ethernet in/out - switch/hub where I can (sort of) daisy chain my boards. (I don't wish to use a ethernet switch/router/hub)
One port would be acting as server
The ...
- 610