Unanswered Questions
746 questions with no upvoted or accepted answers
7
votes
0
answers
394
views
Handling non-standard I2C read response lengths with Wire library
I'm trying to read from a Sam&Wing XW12A 12 channel touch sensor IC using I²C. The IC responds to an address read packet with 16 uninterrupted bits representing its state.
However, since I²C ...
- 171
5
votes
0
answers
361
views
SPI between Master arduino and Slave arduino
How can I send the string from Slave SPI to Master SPI?
I want to write code in Bare Metal.
The problem which I am facing is I can't make out what will be my blocking function in Master SPI code when ...
CommunityBot
- 1
5
votes
0
answers
7k
views
Why is Wire.onReceive() called during requests?
I'm building a complex I2C-based networking protocol and have noticed that the Wire.onReceive() handler is called both for I2C read and write operations. When the master writes to the slave, it is ...
- 2,522
4
votes
0
answers
2k
views
Is there a way to use ESP8266 in promiscuous(monitor) mode and see the the wifi packets?
I didn't find much documentation about ESP promiscuous mode (just from the espressif sdk although I'm using ArduinoIDE https://docs.espressif.com/projects/esp8266-rtos-sdk/en/latest/api-reference/wifi/...
- 73
4
votes
0
answers
9k
views
How do I interpret the esp8266 "boot mode" message?
Everytime the chips resets, we get the reason and the next boot mode.
ets Jan 8 2013,rst cause:XXX, boot mode:(YYY,ZZZ)
For XXX we can check the meaning here.
For YYY and ZZZ I am not sure but I ...
- 225
4
votes
2
answers
137
views
Turn ESP8266 into an Arduino IDE-like "sketch uploader" (over hardware serial)
I have an ESP8266 module which has downloaded a hex file for an Arduino Mega2560. This hex file (call it mega2560.hex) is sitting in the ESP's SPIFFS file system. What I want to do is basically ...
- 18.2k
3
votes
1
answer
165
views
Error trying to play audio through an ESP8266 using the 'ESP8266Audio' library
I am attempting to use an esp8266 to play an .mp3 audio file through a connected speaker using the 'ESP8266Audio' library.
I have tested that the hardware setup is correct (e.g. I have been able to ...
CommunityBot
- 1
3
votes
0
answers
74
views
Why RTU bridge timeout even though answer is received?
I'm testing the following code as a bridge between https://sourceforge.net/projects/qmodmaster/ and https://pypi.org/project/pyModSlave/.
As hardware, I'm using a NodeMCU 1.0 and a USB/TTL converter.
...
- 31
3
votes
0
answers
32
views
is it possible for a client esp8266 to control the esp8266 that set as an access point?
Im creating a project where i need to set one of my esp as a hotspot or access point but i would like to put a function where i could control the connected esp8266 client using the esp8266 that set as ...
- 61
3
votes
0
answers
227
views
Using 2 VL53L4CD ToF sensors and getting error after getting first reading
pretty new to arduino stuff and was hoping to get some help with my code.
I'm trying to use 2 ToF sensors and get continuous readings from them. I understand that I have to use the xshut feature and ...
- 31
3
votes
0
answers
381
views
Raspberry pi pico (Arduino core) not initialising SPI correctly for NRF24l01
I'm working on a project where i have a Raspberry pi Pico connected to a NRF24l01+ to send some data.
However i'm not recieving any data on the reciever and i think that its because the SPI bus is not ...
- 1,525
3
votes
0
answers
1k
views
ESP32-C3 SPI Class documentation/features?
ESP32-C3 has a nice feature called GPIO Matrix which allows to map most of it's peripherals to any GPIO pin. And it has feature called IO_MUX which allows direct & faster operations for some of ...
- 131
3
votes
0
answers
208
views
ESP8266 01 doesn't react after baud rate change
Hello guys I have my ESP8266 connected to my Arduino. Then I typed in AT in the serial monitor. It confirmed this command with OK. After that I typed in AT+UART=9600, 8, 1, 0, 0 which gave me the ...
- 41
3
votes
0
answers
1k
views
ESP8266 Webserver does not respond
I am trying to reach the webserver running in my Wemos D1 Mini compatible board.
I am trying one esp8266 example using Arduino examples "WifiManualServer" code below.
I have replaced the SSI ...
3
votes
0
answers
3k
views
Using or creating Wi-Fi Direct (P2P) connection on ESP8266
I want to make a Wi-Fi Direct connection with an android device using my ESP8266. According to ESP8266WiFi Documentation and ESP8266 datasheet, the board has a SoftAP mode which is I think what is ...
