Unanswered Questions
1,687 questions with no upvoted or accepted answers
6
votes
1
answer
2k
views
Ultrasonic Flowmeter Using TDC-GP22 and Arduino Uno
I'm working on a project of Ultrasonic Flow Meter with TDC-GP22 using Arduino UNO. I used the library of leokoppel
In my code,the configurations of the registers are copied from the Application Note ...
CommunityBot
- 1
5
votes
0
answers
361
views
SPI between Master arduino and Slave arduino
How can I send the string from Slave SPI to Master SPI?
I want to write code in Bare Metal.
The problem which I am facing is I can't make out what will be my blocking function in Master SPI code when ...
CommunityBot
- 1
5
votes
0
answers
2k
views
Modbus TCP/IP using Arduino uno and ENC28J60 module
I have this project where I need a modbus tcp server that will host a series of sensor data for other modbus client devices to read. I use this Library by Andresoarmento
This is the code i am using ...
5
votes
0
answers
419
views
DHT22 reading weird values
I just hooked up a DHT22 I had laying around in a parts drawer to test something and it is giving out some crazy wrong values, I am running the adafruit library's unified example and this is the ...
- 19
4
votes
0
answers
343
views
Is Arduino WiFi101 library fully compatible with Arduino MKR1000 with WiFi HW?
Will all the classes in this library work with the MKR1000 with wifi hardware?
The guide mentions "wifi shield".
So, does the library work exactly the same with the Arduino MKR100 (with the onboard ...
- 201
4
votes
0
answers
737
views
Nordic nRf905 (433MHZ) with arduino receive garbage data
I am interface Arduino with nRf905 in receive mode use 433 MHZ.
I Have follow this link http://www.electrodragon.com/w/NRF905_Transceiver_433MHz-Wireless_Module.
And for transmitter, I am use RF-...
- 2,522
4
votes
0
answers
471
views
Problem in using COZIR W-100 with arduino
I was using the COZIR W-100 carbon dioxide sensor with an Arduino Mega 2560 with the example code from this site.
But the measured value of carbon dioxide by sensor was 90 ppm in fresh air and that ...
4
votes
0
answers
175
views
Can d2xx connect to an arduino mega 250?
I am trying to replace a device which used a FTDI chip (http://www.ftdichip.com/Drivers/D2XX.htm) to get USB to serial. I need some more code on the chip, so I want to use an arduino mega 2560 instead....
- 41
4
votes
0
answers
650
views
RFID Code (and setup) works on an UNO but not on the Yun
We're using two RDM6300 RFID readers for this, and the code works when plugged into an UNO, but not when connected to the Yun. We have one of the rfids plugged into the rx pin (0 on the digital side) ...
4
votes
0
answers
7k
views
Arduino GSM receiving text and then storing value as a variable in code
I am using an Arduino Mega board with a SIM900 GSM.
My goal is to be able to text the GSM with a value of two digits (ex: 79) and then store that value as a variable in the code. I know how to set ...
4
votes
2
answers
137
views
Turn ESP8266 into an Arduino IDE-like "sketch uploader" (over hardware serial)
I have an ESP8266 module which has downloaded a hex file for an Arduino Mega2560. This hex file (call it mega2560.hex) is sitting in the ESP's SPIFFS file system. What I want to do is basically ...
- 18.2k
3
votes
1
answer
151
views
Arduino R3 Uno Clone - When barrel plug connected there is 5V on USB. Why?
I have been using Arudino Megas for some projects and never had this problem.
Simply enough - I am powering arduino with 12V in via barrel and take power out via VIN to 12V low very low current small ...
CommunityBot
- 1
3
votes
0
answers
280
views
Sim800l doesn't respond to AT commands
My SIM800L doesn't respond to AT commands. The serial monitor is simply blank.
And the led blinks every 3 seconds which means it is connected to a network
I power it through an LM2596 buck down ...
- 544
3
votes
0
answers
381
views
Raspberry pi pico (Arduino core) not initialising SPI correctly for NRF24l01
I'm working on a project where i have a Raspberry pi Pico connected to a NRF24l01+ to send some data.
However i'm not recieving any data on the reciever and i think that its because the SPI bus is not ...
- 1,525
3
votes
0
answers
490
views
Integration of MAX30100 and DS18B20 Thermal Probe Integration
This is for my final year project that I have been tasked with designing a patient monitoring system. However, during the last stretch of model prototyping, I am experiencing issues with my MAX30100 ...
