Unanswered Questions
368 questions with no upvoted or accepted answers
4
votes
0
answers
76
views
Can I use regular pins (Example: D2, A3, etc...) as serial (RX, TX)?
Python/Arduino Beginner here...
I have a DFplayer I am trying to hook to my Arduino and I want to hook it up through the regular pins instead of the RX and TX pins, but I've not been able to find ...
- 41
3
votes
0
answers
78
views
nano 33 BLE problems with reading RC signal
I'm using an Arduino Nano 33 BLE and a L293D motor driver to control a three-wheeled RC robot. The sketch I'm using worked fine with my Uno Rev3, but I've moved to the Nano for size/weight reasons, ...
- 1,042
3
votes
0
answers
191
views
Grove LCD display not working with arduino rev 2 wifi (Unknown error at address 0x3E)
I am trying to connect Grove 16x2 LCD (White on Blue) to my Arduino uno rev 2 wifi.
So far, I've tried hd44780 library's ioClass examples, but nothing worked. I've then decided to scan ports and when ...
- 31
3
votes
0
answers
105
views
My port is grayed out?
Hello I have a question on why my port is grayed out when I go to upload?
I’ve watched so many YouTube videos on what’s the problem and have been trying to do everything but just nothing seems to work!...
- 1,795
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
0
answers
601
views
Do software SPI read from a register using shiftin()
How to read from a register using software SPI, presumably shiftin()?
It works using the builtin SPI library + hardware SPI.
I seem to be able to write but not read using manual shiftin()/shiftout()...
- 3,198
3
votes
0
answers
700
views
Serial does not work when LiquidCrystal library is used
I have been struggling with a LCD for 6 hours straight - I've had many problems including random characters showing up, and this time (not quite sure what changed, I tried so many things) as soon as I ...
- 2,522
3
votes
0
answers
397
views
How do I install a library in Arduino Yun cross compile environment?
A few days ago, I've asked this question.
Thanks to the replies I've received, I've set up a cross compile environment for Yun by following this guide.
I've created a virtual machine with virtualbox ...
CommunityBot
- 1
3
votes
1
answer
1k
views
3.5 inch TFT LCD connection diagram with mega r3
Forum post
I would like to ask if someone has this shield fully working?
My biggest problem is the touch screen that I couldn't manage to make work.
Here is the code I am using:
// ic: ili9327
#...
CommunityBot
- 1
3
votes
0
answers
2k
views
Arduino sketch works on ATmega1280, but doesn't work on ATmega328 (Arduino Nano)
I'm working on arduino based RGB LED strip controller.
This simple schematic was used to control 12V channels via 5V PWM signal from arduino:
I have also connected an HC-05 bluetooth module to be ...
- 471
2
votes
1
answer
83
views
Code for a load cycler seems to be stuck
I am trying to make a battery load cycler to charge and discharge a battery repeatedly for a certain amount of cycles and here is my code:
bool in_charge_mode;
int cycles = 0;
float cutoffvoltage = 2....
CommunityBot
- 1
2
votes
0
answers
80
views
My code got my Nano ESP32 into a <500ms reboot loop
I have done a lot of reading and learning after previous help here and it has been great.
I have uploaded and tried many iterations of my code which all worked (Assuming my code was actually good) and ...
- 21
2
votes
0
answers
284
views
Arduino NANO RF reciever and Digispark Attiny 85 transmitter issues
I am trying to send RF signal from Digispark Attiny 85 (this one) and receive the signal with Arduino NANO V3.0 ATmega328 (this one). Transmitter and receiver are STX882 and SRX882 (these). Library ...
- 1
2
votes
0
answers
85
views
Arduino code intermittent
Have an alarm for "tea time", "lunch time" and "tea time". Works well at times but occasionally it gets stuck on the alarm not resetting, other times it does not trigger ...
- 544
2
votes
0
answers
99
views
How to show repeated result on LCD while button is pressing
my results are here.
0 press--"a"
1st press--"b"
2nd press--"c"
3rd press-- still showing "c"
When button pressed 3rd time, It must be repeated to show "a&...
- 5,514