Unanswered Questions
195 questions with no upvoted or accepted answers
4
votes
0
answers
718
views
ArduinoDue - Matlab: SerialUSB.write() sends ASCII?
I'm trying to get some binary data from an Arduino Due to Matlab.
Basically this is the setup:
Due:
byte usbMsg[33]= {0};
// filled with dummy as example
usbMsg[1] = '00000001';// in[3];
usbMsg[2] =...
- 2,522
3
votes
0
answers
204
views
Black screen when using higher SPI-speed for RA8857 LCD-controller
I'm using an Arduino Due that talks via SPI to an LCD (800x480) with the RA8875 controller chip.
The most recent datasheet I could find is: RA8875 datasheet.
Everything works as expected when using ...
- 155
3
votes
0
answers
713
views
Getting atsam3x8e (Arduino Due) to work
I decided to make a pcb based on the atsam3x8e (microcontroller used in Arduino Due). For the design I copied most of the layout that I found on this site and looked at the official Arduino Due ...
3
votes
1
answer
2k
views
Creating a sine wave with a DAC and feeding it back
I want to produce a digital sine wave, send it to DAC0, and then receive it back as input on A0 and plot the graph. I am using an Arduino Due. I wrote the following code:
#define maxSamplesNum 120
#...
CommunityBot
- 1
3
votes
0
answers
378
views
Connecting Arduino Due's DAC output to pc sound card with protection
I would like to connect the DAC outputs of my arduino board to my pc sound card input so that I can use my sounds card as an osciloscope.
I have two questions:
1- if I don't use an amplifier, how ...
- 241
3
votes
0
answers
129
views
Reading Reveive Hold Register from USART in SPI Mode on Arduino Due
Sending with this function here works fine:
uint16_t usart0spiTransfer16(uint16_t spiMessage16) {
uint16_t sdo = 0;
byte firstByte = spiMessage16;
byte secondByte = (spiMessage16 >> ...
- 2,522
3
votes
0
answers
323
views
Arduino Due upload firmware issue
I have Arduino Due on SAM3x8e. I'm on Ubuntu 14.04. Before today I uploaded firmware via terminal using those commands:
$ stty -F /dev/ttyACM0 speed 1200 cs8 -cstopb -parenb
$ /home/q/apps/devel/...
- 151
3
votes
0
answers
883
views
Arduino Due native programming port
Arduino does not recommend to program the Due board via Native port as it is not reliable:
If the MCU crashed for some reason it is likely that the soft erase procedure won't work as this procedure ...
- 111
3
votes
0
answers
1k
views
Interfacing WM8731 code to Arduino Due
WM8731 codec was successfully interfaced with Atmega328 like variants in Arduino. It was first done successfully by Open music labs who are the makers of the breakout board for WM8731. Taking this ...
- 2,522
3
votes
0
answers
2k
views
Arduino sketch works on ATmega1280, but doesn't work on ATmega328 (Arduino Nano)
I'm working on arduino based RGB LED strip controller.
This simple schematic was used to control 12V channels via 5V PWM signal from arduino:
I have also connected an HC-05 bluetooth module to be ...
- 471
3
votes
1
answer
785
views
ov2640 with 18 pin and no arducam shield
I bought this ov2640 camera module with 18 pins and I don't have shield to insert it to. I am looking for a library or working code on this my camera sensor but all I kept getting was arducam examples ...
- 31
2
votes
1
answer
111
views
Transmitting voice via VLC
The project I'm working on: Short-Range Coded Visible Light Communication System.
Visible Light Communication (VLC) systems use light to transfer data between transmitter and receiver over short-range ...
CommunityBot
- 1
2
votes
0
answers
130
views
On initialising PWM with registers on my Due, why does unrelated duty cycle input influence my output?
I am finding that setting duty cycle on PWM channels 4 or 5 has an influence on whether channel 6 generates output. The following is a design of experiments view of my tests and results, where the ...
- 295
2
votes
0
answers
426
views
Using ICSP pins as SPI in Arduino Due
I am using two RFID sensors operating on SPI with arduino Due. They will not be operating at the same time.
Is it favorable to use the ICSP pins as SPI pins for one of them, or use them in a one ...
- 121
2
votes
0
answers
87
views
Servo wont work with LED code!
I'm basically trying to combine my servo code and my LED code but whenever I add my servo code the LED refuses to turn on at all.
I am super new to arduino sorry if this doesn't make any sense!
Servo ...
- 15.4k